VAS 5054A ODIS-S v.2.2.3 +Postsetup v.6.20.25

Volkswagen Group newest diagnose software support 2014.12 all Volkswagen , Audi , Seat ,Bentley . Lamborghini

Over 39 GB

Full license

Get download link here

Buy VAS 5054 diagnostic Adapter from xcar360 

Mercedes-Benz key tool support NEC 57

 Mercedes-Benz key tool for Mercedes-Benz support NEC 57 is the most powerful Benz key programmer in the world that support NEC. No need disassemble, support read EIS data via IR. Many more functions is included only in Advanced benz key Programmer.

Note: This product is don't support Calculate Function, used together with MB Dump Key Generator from EIS Super SKC Calculator .

 Mercedes-Benz key tool  Programmer Functions:

- Directly read data from EIS via infrared (easy and convenient). Unnecessary to detach.

- Support Password of reading NEC key 57, Calculate new lock data under EIS help, and reborn a new key.

- Equipped with EB KEY, Read, Write and erase data in myriad with convenience, Our machine is fully compatible with original key material, nothing to worry about.

- Get EIS data after reading, Operate with SKC key software, and reborn the key that you want Convenience and offline mode.

Upgrade:

- Read & get Password (908, p12 MCU) via infrared from EIS. even if all keys lost, don't need to detach anywhere. Directly reborn a new key.

- We will launch W204 212 electrical lock cylinder function soon.

Supported Car Models:

A-class W169 2004-2010

B-class W245 2005-2010

C-class W203 2003-2007

CLK-class W208 2001-2002

CLK-class W209 2003-2008

C-class W204 2007-2009

E-class W210 2001-2002

E-class W211 2002-2007

E-class W212 2009-2010

CLS-class W219 2004-2009

S-class W220 2001-2005

S-class W221 2005-2009

CL W215 2001-2006

CL W216 2005-2009

SL R230 2001-2009

SLK R171 2004-2009

G-class W463 2002-2009

R-class W251 2005-2009

M-class W164 2005-2009

GL-class X164 2006-2009

Vito/Viano W639 2004-2009

Sprinter W906 2005-2009

All these cars are available as long as the key is to increase the 57 subsequent versions will add other cars.

Software display:

1. Key Module

2. EZS Module

1. Load file

2. To read PSW from IC 57 version keys.

3. The device can read PSW through IR from after market MB keys. (Will update soon)

4. To read or write key through IR. (Click the circle twice)

5. To renew the original chips on early type programmer adapter.

6. For IC 57 version programmer adapter to read PSW. (Only for 57 version key)

7. Click to renew the original chips. (Click again to cancel.)

8. Program

9. Read

1. For IC 57 keys to read PSW.

2. Read PSW.

3. Click to save PSW after you read out from the chips.

mercedes 722.9 VGS Offline Replace Step by Step instructions using AVDI

722.9 VGS Offline Replace Step by Step instructions using AVDI:

Buy avdi mercedes commander from xcar360
Well, here we go: Your machine must be offline enabled and flash data mounted!!!! 
Read out/save SCN coding and EHS# from vehicle using OBDII connector 
Printout your control unit version page 

Set up virgin vgs to avdi on bench using the obd connector according to the following: 
1. 12v to pin 16 on OBD and pin 4 on ETC 
2. CAN HIGH pin 6 on OBD->>>pin 1 on ETC
3. CAN LOW pin 14 on OBD--->>>pin 2 on ETC 
4. Signal GROUND pin 5 on OBD---->>>>pin 5 on ETC 
5. Chassis GROUND pin 4 on OBD----->>>ground on power-supply 



Transfer SCN coding and EHS# you saved into the virgin VGS -->Replace VGS -->Plug in old control module to car(I let it hang from connector) -->Go into development data in ETC->control unit adaptations->Read coding and/or transfer download data to new control unit -->follow the next steps(it will say that not all coding can be exchanged....(its ok) after you plug back in and it transfers coding it will say not all data could be exchanged, do you want to do manual settings now? say later/NO -->On main ETC page -->control unit version, make sure your EHS# matches the original from the control unit version page you printed out, just the EHS# must match, If it does not match goto -->development data---> control unit adaptations(download) --> ZBEHS -->enter the original EHS# from control unit version sheet you printed at the very beginning of job. 1 means it was transferred  Well, now in the Main ETC page --> Control unit adaptations -->control module programming -->offline programming -->hard disk data. (I use a LAN cable with my C4 for this just to make sure complete programming will be successfully done  -->control unit adaptations --> detach transport/personalize/activate -->follow prompted steps. Done! 

Please note that: this process has been proven and tested on cars with VGS2 and newer only